Possible Problems With The Brake Pads

Brake pads are an indispensable part of the car brake system. During normal driving, we may encounter the phenomenon that the brake pads are hot or uneven. Some friends will ask what is going on here. The following Mazda Brake Pad Exporter will Tell us about the cause of the problem with the brake pads and how to solve them.

If the brake pads are hot, you can push the front wheel of the car up and turn the tire to see if it does not rub. Then turn the tire and try a few brakes to see if the brake's return card is not stuck. If the tire is not flexible, it means there is interference in the brake pad. If the brake does not return or the brake is slow, then the brake system has The problem needs to be repaired in time.

AUDI Brake Pad

The tire is at the innermost part of the brake pad, that is, the shaft head that sees the bearing is installed after disassembling. The shaft hair is generally caused by over-tightening or poor lubrication of the bearing. If the temperature is too high, the grease melts inside. It will affect the braking effect and will burn the bearing when it is serious. If the shaft is hot, be careful. It may be that the bearing inside is too tight or abnormally worn, and the bearing can be properly adjusted.

It is well known that as long as the brakes are applied, the brake pads of all the cars will be hot. The faster the car, the higher the weight, the higher the heat of the brakes. This is the principle of energy replacement. However, if the brakes of your car brakes have become normal, you should pay attention to the above problems and need to be replaced in time. , according to the type of vehicle replacement, such as Ferrari Brake Pad.

Stepping on the brakes is a problem that many people have encountered, which is caused by uneven brake pads. However, there are many reasons for the unevenness of the brake pads. Therefore, when we encounter such problems, we cannot generalize and learn to analyze the causes according to the phenomenon:

One: shake the brakes when you hit the brakes at medium and high speeds

When the brakes are shaken at high speed, it is caused by the unevenness of the brake pads. When the components are unbalanced during rotation, vibrations are generated. This vibration is mainly generated on the tires.

Solution:

It is recommended to change the place to do a four-wheel balance to see if the problem is solved to eliminate the possibility of the tire causing the malfunction. If you still shake, check the following half shaft, shaft head and other related parts. When the road is not flat, the car will be biased to the right. Because the road design should consider the problem of drainage, it is impossible to do it very flat. If it is also on a very flat road, check it in the place where it should be repaired.

Two: lightly stepping on the direction of the car

This situation indicates that the flatness of the front brake pad has exceeded the required range. This means that the front brake pads are not flat. During the process of stepping on the brakes, the left and right brake pads will clamp the brake pads. If the brake pads are not flat at this time, the brake pads will have a radial force, and the force will change back and forth at a very fast speed. The wheel is also responsible for the steering effect, which causes the direction to shake under the driving of the front wheel.

Solution:

Go to the repair shop for inspection. If the thickness of the front brake pads is allowed to be solved by polishing the brake pads, if the brake pads are already below the ultimate thickness or close to the limit thickness, only the brake pads can be replaced.

Three: lightly step on the brake body

In this case, the rear brake pads are not flat or the rear brake drums are not round, causing the entire body to shake, especially when the rear wheels are drum brakes. This is because the rear wheel does not have the role of steering, and the force transmitted directly from the brakes is transmitted to the body to cause the entire body to shake.

Solution:

Go to the repair shop for inspection. If the thickness of the rear or rear brake drum is allowed to be solved by the light brake pad or the light brake drum, if the brake pad or brake drum is already below the limit thickness or close to the limit thickness, it can only be replaced to solve.

In fact, stepping on the brakes is nothing more than just a few cases. According to the different jitter phenomena, we can easily determine what caused the problem, and then maintain or replace the brake pads according to the actual situation.

The above will lose the cause and solution to the problem with the brake pads, I hope to help everyone. If you have a need for brake pads, you can contact us, we will produce brake pads for all types of vehicles including AUDI Brake Pad , welcome you.